Omron Programmable Terminals NT31 NT31C Manual de usuario Pagina 214
- Pagina / 296
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6-11SectionSystem Maintenance
204
Display the SCREEN DATA CHECK screen by following the menu operation
from the System Menu shown below.
Select Maintenance Mode.
Select Screen Data Disp.
Specify the screen to be displayed in the input
field in the middle of the screen.
Each of the digits can be incremented or
decremented by pressing the associated +
and − keys.
Press Set.
Press the touch switches to specify the dis-
play method in each case.
The setting option changes each time a touch
switch is pressed.
Ver 3.10
Displaying the SCREEN
DATA CHECK Screen
- Setup Manual 1
- NT31and NT31C 2
- Programmable Terminals 2
- OMRON Product References 4
- Visual Aids 4
- TABLE OF CONTENTS 6
- About this Manual: 8
- Related Manuals: 9
- PRECAUTIONS 10
- 2 General Precautions 11
- 3 Safety Precautions 11
- 1 Intended Audience 11
- 3Safety Precautions 12
- SECTION 1 13
- Production Control (3) 14
- % achieved 14
- Electroplating control 14
- 1-2-1 Features 16
- 1-2-6 Displays 23
- Mark Image data Library data 24
- Image/library 27
- 1-3 System Configuration 28
- 1-3-2 Connecting to the Host 29
- 1-4-2 Host Link 30
- 1-4-3 NT Link 30
- 1-5-1 Memory Link 32
- 1-6 Before Operating 34
- 1-6SectionBefore Operating 35
- SECTION 2 36
- Preparing for Connection 36
- Front View 40
- Rear View 41
- SECTION 3 42
- 3-1 Installation 43
- 3-1-3 Power Supply Connection 44
- 3-1-4 Grounding 45
- Serial port A 46
- (RS-232C, 9-pin) 46
- 3-3 Connecting a Printer 47
- 3-4-1 Connection Method 48
- 3-4-3 Data Format 49
- 3-5-1 Installation Method 51
- 3-5-2 Method of Use 51
- Setting of SW1-4 not relevant 55
- Setting of SW2-3 not relevant 55
- Setting of SW2-4 not relevant 55
- 3-6-1 Installation Method 59
- 3-6-2 Method of Use 59
- SW2-3 ON: Bank 1 60
- OFF: Bank 0 60
- SECTION 4 64
- 4-1-1 Host Types and Settings 65
- CS1W-CN118 Connecting Cable 66
- Setting the Front Switches 68
- CQM1H CPUs, SRM1 73
- PROGRAMMABLE CONTROLLER 78
- Set this to RS-232C 82
- Set SW3 to use NT link 82
- (ON, right side) 82
- DIP switch setting (SW3) 82
- Setup effective 84
- Shielding wire 92
- ⇔25-pin, 2 m) 94
- ⇔9-pin, 2 m) 94
- Serial Port B 95
- SECTION 5 96
- NT-AL001 99
- Functional 100
- ⇔ 25-pin, 2 m) 101
- ⇔ 25-pin, 5 m) 101
- (marked 106
- in the figure above) only 106
- in the figure above) 107
- Fork type 110
- 6.2 mm or less 110
- Round type 110
- RS-422A cable 111
- (max. 500 m) 111
- 5-2-1 Host Types and Settings 112
- RS-422A Adapter to connect 113
- LocalHost 115
- Setting the Rear Switches 116
- I/O port selector switch 119
- 4 WIRE 126
- PRINTER PORT B 136
- SECTION 6 141
- System Menu Operation 141
- 6-2 Starting the NT31/NT31C 144
- Transmit Mode 145
- Maintenance Mode 145
- Expansion Mode 145
- 6-3-2 Menu Tree 147
- RUN mode 148
- Press any two of the four 148
- Ver 3.10 149
- 6-4 Memory Initialization 150
- 6-5-4 Clearing Screen Data 164
- Using Memory Switches 167
- 6-8 Starting Operation 178
- 6-9 System Settings 178
- 6-9SectionSystem Settings 179
- 6-11 System Maintenance 201
- 6-11SectionSystem Maintenance 202
- 6-11-6 Checking Screen Data 212
- 6-11-7 Device Check 215
- 6-11-8 Checking Interfaces 225
- 6-12-1 Usable Systems 231
- 6-12-2 Connection Method 233
- 6-12-3 Method of Use 234
- Mode selection keys 235
- Mode lock key 235
- 6-13 Device Monitor Function 237
- 6-13-1 Compatible Systems 238
- 6-13-2 Connection Method 238
- 6-13-3 Method of Use 239
- 6-14 Version Display 240
- SECTION 7 241
- 7-1 Troubleshooting 242
- 7-1SectionTroubleshooting 243
- 7-3-1 Replacing the Battery 254
- 7-4 Inspection and Cleaning 255
- Appendix A 257
- Performance Specifications 258
- Programming Environment 259
- Special Features 259
- Appendix ASpecifications 260
- Communications Specifications 261
- For a Bar Code Reader 263
- Appendix B 264
- Mounting Dimensions 265
- Appendix BDimensions 266
- NT–AL001-E 267
- Removal from a DIN Rail 268
- Specifications 269
- Pin Arrangement 271
- Block Diagram 272
- Appendix D 273
- Appendix E 274
- Soldering 275
- Hood Assembly 275
- Appendix F 276
- Appendix G 277
- Appendix H 278
- Appendix I 279
- Appendix J 281
- Appendix JModel List 282
- Cables with Connectors 285
- Connection Cable 285
- Applicable Connectors 285
- Printer Cable 286
- Appendix K 287
- Memory Unit ... NT-MF261 288
- View angle, 248 292
- Warning label, 30 292
- Waterproofed, 4 292
- Weight, 247 292
- Revision History 293
- Authorized Distributor: 295
Relacionado con productos y manuales para Hardware Omron Programmable Terminals NT31 NT31C
Hardware Omron E7 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Omron CQM1H-CLK21 Manual de usuario
(401 paginas)
(401 paginas)
Hardware Omron DR 170 14 Manual de usuario
(67 paginas)
(67 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales